Trying to create a BIN from a BGA 153 and keep getting an error. The error is Read Check Failed, Error: -206 ,Reason: PORT Read Error . The chip should be 8 GB
This is the log from Z3X
Found 1 serial devices
COM90 USB\VID_0325&PID_0032&REV_0100&MI_00 Easy Jtag Control Port (COM90)
Selected pinout: EasyJTAG GEN1 ISP Pinout
Change EasyJTAG Pinout OK
Compression is ON
Z3X EasyJtag Software ver. 3.1.0.0
Loading eMMC GEN1 Firmware... IO: 2800 mV
Box S/N: 04FFE01DB0EBEC40, ,FW Ver.: 01.63
CMD Pullup Level:1155 mV
CMD Active Level:2774 mV
Box IO Level:2800 mV
CLK Rate:7000 kHz
Bus Width:1bit,SDR
HiPower mode is ON!
---------- eMMC Device Information ----------
eMMC CID : 65646F4D204D4F521290000002400118
eMMC CSD : D07FFF320F59007FF6DB80001E40001C
eMMC Manufacturer ID: 0065 , OEM ID: 646F
eMMC Date: 00/2014 Rev.0x90
eMMC NAME: M MOR , S/N: 576
eMMC NAME (HEX): 4D204D4F5220
EMMC ROM1 (Main User Data) Capacity: 128 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x78] Boot from:ROM1 (Main User Area)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x78.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00000400]
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: M MOR _ 576_20180821_1448.extcsd
Done.
Z3X EasyJtag Software ver. 3.1.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1155 mV
CMD Active Level:2774 mV
Box IO Level:2800 mV
CLK Rate:7000 kHz
Bus Width:1bit,SDR
Reading 0x000800000000 (32.0GB) from 0x000000000000 ...ROM1 (BOOT1 ROM)
Read Length has been corrected to 0x000000200000 (2.0MB)...
Output file :C:\Users\pslpd\Desktop\EMMC_ROM2_M_576_00000000_0 0200000.bin
Read Check Failed, Error: -206 ,Reason: PORT Read Error
Done.
Any help ?
This is the log from Z3X
Found 1 serial devices
COM90 USB\VID_0325&PID_0032&REV_0100&MI_00 Easy Jtag Control Port (COM90)
Selected pinout: EasyJTAG GEN1 ISP Pinout
Change EasyJTAG Pinout OK
Compression is ON
Z3X EasyJtag Software ver. 3.1.0.0
Loading eMMC GEN1 Firmware... IO: 2800 mV
Box S/N: 04FFE01DB0EBEC40, ,FW Ver.: 01.63
CMD Pullup Level:1155 mV
CMD Active Level:2774 mV
Box IO Level:2800 mV
CLK Rate:7000 kHz
Bus Width:1bit,SDR
HiPower mode is ON!
---------- eMMC Device Information ----------
eMMC CID : 65646F4D204D4F521290000002400118
eMMC CSD : D07FFF320F59007FF6DB80001E40001C
eMMC Manufacturer ID: 0065 , OEM ID: 646F
eMMC Date: 00/2014 Rev.0x90
eMMC NAME: M MOR , S/N: 576
eMMC NAME (HEX): 4D204D4F5220
EMMC ROM1 (Main User Data) Capacity: 128 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x78] Boot from:ROM1 (Main User Area)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x78.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00000400]
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: M MOR _ 576_20180821_1448.extcsd
Done.
Z3X EasyJtag Software ver. 3.1.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1155 mV
CMD Active Level:2774 mV
Box IO Level:2800 mV
CLK Rate:7000 kHz
Bus Width:1bit,SDR
Reading 0x000800000000 (32.0GB) from 0x000000000000 ...ROM1 (BOOT1 ROM)
Read Length has been corrected to 0x000000200000 (2.0MB)...
Output file :C:\Users\pslpd\Desktop\EMMC_ROM2_M_576_00000000_0 0200000.bin
Read Check Failed, Error: -206 ,Reason: PORT Read Error
Done.
Any help ?
